SWMM 5 Error Messages - File Errors
| ERROR 301: | files share same names. |
The input, report, and binary output files
specified on the command line cannot have the same names.
| ERROR 303: | cannot open input file. |
The input file either does not exist or
cannot be opened (e.g., it might be in use by another program).
| ERROR 305: | cannot open report file. |
The report file cannot be opened (e.g., it
might reside in a directory to which the user does not have write
privileges).
| ERROR 307: | cannot open binary results file. |
The binary output file cannot be opened
(e.g., it might reside in a directory to which the user does not have write
privileges).
| ERROR 309: | error writing to binary results file. |
There was an error in trying to write
results to the binary output file (e.g., the disk might be full or the file size
exceed the limit imposed by the operating system).
| ERROR 311: | error reading from binary results file. |
The command line version of SWMM could not
read results saved to the binary output file when writing results to the report
file.
| ERROR 313: | cannot open scratch rainfall interface file. |
SWMM could not open the temporary file it
uses to collate data together from external rainfall files.
| ERROR 315: | cannot open rainfall interface file xxx. |
SWMM could not open the specified rainfall
interface file, possibly because it does not exist or because the user does not
have write privileges to its directory.
| ERROR 317: | cannot open rainfall data file xxx. |
An external rainfall data file could not be
opened, most likely because it does not exist.
| ERROR 318: | date out of sequence in rainfall data file xxx. |
An external user-prepared rainfall data file
must have its entries appear in chronological order. The first out-of-order
entry will be listed.
| ERROR 319: | unknown format for rainfall data file. |
SWMM could not recognize the format used for
a designated rainfall data file.
SWMM was trying to read data from a
designated rainfall interface file with the wrong format (i.e., it may have been
created for some other project or actually be some other type of file).
| ERROR 321: | no data in rainfall interface file for gage xxx. |
This message occurs when a project wants to
use a previously saved rainfall interface file, but cannot find any data for one
of its rain gages in the interface file. It can also occur if the gage uses data
from a user-prepared rainfall file and the station id entered for the gage
cannot be found in the file.
| ERROR 323: | cannot open runoff interface file xxx. |
A runoff interface file could not be opened,
possibly because it does not exist or because the user does not have write
privileges to its directory.
| ERROR 325: | incompatible data found in runoff interface file. |
SWMM was trying to read data from a
designated runoff interface file with the wrong format (i.e., it may have been
created for some other project or actually be some other type of file).
| ERROR 327: | attempting to read beyond end of runoff interface file. |
This error can occur when a previously saved
runoff interface file is being used in a simulation with a longer duration than
the one that created the interface file.
| ERROR 329: | error in reading from runoff interface file. |
A format error was encountered while trying
to read data from a previously saved runoff interface file.
| ERROR 331: | cannot open hot start interface file xxx. |
A hotstart interface file could not be
opened, possibly because it does not exist or because the user does not have
write privileges to its directory.
| ERROR 333: | incompatible data found in hot start interface file. |
SWMM was trying to read data from a
designated hotstart interface file with the wrong format (i.e., it may have been
created for some other project or actually be some other type of file).
| ERROR 335: | error in reading from hot start interface file. |
A format error was encountered while trying
to read data from a previously saved hotstart interface file.
| ERROR 336: | no climate file specified for evaporation and/or wind speed. |
This error occurs when the user specifies
that evaporation or wind speed data will be read from an external climate file,
but no name is supplied for the file.
| ERROR 337: | cannot open climate file xxx. |
An external climate data file could not be
opened, most likely because it does not exist.
| ERROR 338: | error in reading from climate file xxx. |
SWMM was trying to read data from an
external climate file with the wrong format.
| ERROR 339: | attempt to read beyond end of climate file xxx. |
The specified external climate does not
include data for the period of time being simulated.
| ERROR 341: | cannot open scratch RDII interface file. |
SWMM could not open the temporary file it
uses to store RDII flow data.
| ERROR 343: | cannot open RDII interface file xxx. |
An RDII interface file could not be opened,
possibly because it does not exist or because the user does not have write
privileges to its directory.
| ERROR 345: | invalid format for RDII interface file. |
SWMM was trying to read data from a
designated RDII interface file with the wrong format (i.e., it may have been
created for some other project or actually be some other type of file).
| ERROR 351: | cannot open routing interface file xxx. |
A routing interface file could not be
opened, possibly because it does not exist or because the user does not have
write privileges to its directory.
| ERROR 353: | invalid format for routing interface file xxx. |
SWMM was trying to read data from a
designated routing interface file with the wrong format (i.e., it may have been
created for some other project or actually be some other type of file).
| ERROR 355: | mis-matched names in routing interface file xxx. |
The names of pollutants found in a
designated routing interface file do not match the names used in the current
project.
| ERROR 357: | inflows and outflows interface files have same name. |
In cases where a run uses one routing
interface file to provide inflows for a set of locations and another to save
outflow results, the two files cannot both have the same name.
| ERROR 361: | could not open external file used for Time Series xxx. |
The external file used to provide data for
the named time series could not be opened, most likely because it does not
exist.
| ERROR 363: | invalid data in external file used for used for Time Series xxx. |
The external file used to provide data for
the named time series has one or more lines with the wrong format.
No comments:
Post a Comment